XRIDONSEN 2PCS 70 inch Emergency Truck Police Lights Strip 864 LED Running Board Strobe Lights Red Blue Police Lights Flashing Warning Hazard Safety w/Waterproof Flexible for Vehicles Trucks Pickup

It is a great product and works better that description leads you to believe . They lights are easy to install and are very bright and has held up to the rain, dirt and mud very well .

I purchased these to put on my fire Chief Tahoe they fit so nice and give added lighting for approaching intersections they are durable and really can be placed anywhere! Great product can be seen day and night priced great as well

Was an easy install and the brightness and patterns are great. Ive had this installed for a few months now and it hasnt given me any issues at all. At 1st i was worried that is may come off but between the plastic locks and the double sided tape its done great. It has been put through rain, snow, and ice with no issues. Item is used on a specilized vehile and has done awesome for the price. I would definitely recommend this product.

The media could not be loaded.  Be sure to clean well before install. Really easy to install and very bright. Lots of patterns. It was 45deg when installing. I had these hangung with my shop heater on and let these unravel while warm as i cleaned and prepped. I used 3M double stick tape first, stuck these on, then heat gun to ensure adhesion. My running boards aren't solid so had to mount them kinda hidden away on the rockers. They're not very noticeable during full sun but cloudy/rainy/night They're extremely bright. Still very cool. Wish there was a manual for hard wire option to connect to upfitter switches for pattern select. I believe I can figure it out, but don't want the plug in my 12v outlet permanently. Overall great and I recommend it.

The media could not be loaded.  I had previously asked whether these can be cut to size. The answer, without exception, was no. I have added the red/white to my Sequoia luggage rack on the left and right side - the 70" was perfect in length. I added a third to my existing 52" curved white LED light bar. But since the 70" was too long, I had to cut the strip. Since the end with the cables seems to be fused in plastic, I opted to remove the opposite end. I cut the plastic tube without damaging the LED strip. I then pulled the strip out as far as it would go (stretching it), and cut it. This let the strip slide back into the tubing by about 1/2". I then sealed the open tubing with clear caulking.It is important not to allow the tubing/strip to experience any temperature changes while the caulk dries - else it will suck it in (if it gets cooler) or push it out (if it gets hotter).The results are fantastically bright LEDs above the roofline that can be seen from hundreds of yards away. In fact, these were brighter than the mounted emergency light bars I had previously installed - so I removed them.The beauty is that the strips all but vanish against the black luggage rack and light bar - until they're turned on. And with the larger light bars gone, I don't look quite so dorky/obvious.I used standard rubbing alcohol with paper towels to prep the surfaces. The 3M VHB tape on the back of the strips are really stuck on there. The luggage rack is relatively smooth, so I expect them to hold without any further adhesive measures (i.e. zip ties or screws).

I purchased these hoping they were going to add some lighting to the side of my fleet vehicles and decided to give these a try. Being that our fleet vehicles make frequent stops along roadways and highway for inspections. Right out of the box seemed to be decent. I throughly cleaned the area where directions instruct for installation. Installed the light strips with two supplied brackets on both strips and screws on the end of the strips. The lights were installed in a climate controlled shop. The next morning pulled out of the shop and took a 15 mile drive at approximately 45 mph and heard a loud noise and saw the cord pull then snap. Apparently, the adhesive failed and flew underneath the back tire of the truck. The adhesive was still on the side of the truck but the light strip on the passenger side was gone with the wind. And the drivers side ways barley still on. When illuminated they were decently bright. I guess I will be searching for a similar product for the rest of my fleet vehicles. Apparently, I can’t return them since the one of the strips is who knows where. Did not even last 12 hours on the vehicle. I really wished they worked. I would hope they make it right.

The lights are Super bright easy to install and a good amount of wire to run in your vehicle.

These will knock ya eyes out! Great lights! Definitely will buy more!

The media could not be loaded.  Very bright durable. Really gets your attention!!!Standing up to the cold Canadian winter and working great so far!!