Suncast 4 Cubic Feet Resin Single Shelf Garage Wall Storage Cabinet, Platinum

So everyone can see I bought the Suncast plastic water resistant waterproof cabinet to store all of the grill tools that I also purchased from Amazon. It makes for a very easy way to organize. I just use one by two wood strips painted in black pegboard painted it black and now I can hang all the tools that I need between the grill and the griddle. Not difficult to put together, for our needs, we are placing it between a griddle and a grill. I put pegboard inside to hold all of the cooking utensils for the outdoor grill and griddle. Great quality went together. Well doors closed very well. Has a nice mounting bracket underneath it to where you can mount it to whatever source you wanna mount it to it would be suitable for inside or outside.

This is a great little cabinet.It's sturdy. pretty easy to put together.. relatively easy to mount.Keep some things in mind.1. There are no pre-drilled holes for getting wires into the the cabinet.This might not be a concern in your application, but I'm using this to keep a tv and "amplifier" safe from the elements on my back porch.I drilled two holes (one on top and one on bottom, both to run power cables through). I filled the holes with paper towels and a strip of duct tape on both sides to keep any homeless wasps out.2. The shelf can only mount in one location. It was too low to allow my tv to fit, and I wanted/needed the shelf. I just cut some small 1/2 inch plywood strips and screwed them into the plastic where desired. The shelf sits on these fine. Obviously this probably isn't as strong as the original design, but I'm only holding up a couple of pounds.3. There aren't any concrete anchors for the mounting screws. So if you're planning on mounting to brick/similar keep that in mind.I replaced the included lug nuts with some tapcon concrete screws (3/16th x 1-1/4 on the bottom and 3/16th x 2-3/4th on top). Works great.4. There's nothing included to hold the doors open. So (again if your application is similar to mine) you might get the doors slammed shut once in a while by the wind. There's a bazillion "fixes" for that. I'm using a bungee cord temporarily..Despite these minor hurdles I'm very satisfied with this cabinet. It looks 100 times better than my previous, ghetto 2x4 shelf and tarp setup. Not to mention, it's a lot more functional as well.

I own 2 of these, and they're perfect for a garage that gets humid. The installation is easy, and it DOES NOT have to be wall mounted. I have the second one on the floor next to the washing machine, and I reversed the door installation so that the handles are situated up top. Do take note of the depth which is not as deep as other MDF cabinets made for garages or laundry rooms. And the shelf locks into place right in the middle of the cabinet and you cannot move it up and down. So take note of the height of your bottles or whatevers before purchasing it.

A well-made, sturdy cabinet. Good design features giving it strength, particularly the shelve cross-supports. It is large enough in the vertical and width dimensions for my uses; however, shelf depth is but nine inches. For my purposes, a bit more depth would have accommodated my "grand scheme" of items to store. Only reason for the one star deduction.Couple of notes on assembly and mounting. Follow the directions, particularly the first few steps in the attachment of the sides and back to the base - once they snap in, they're in. The upper mounting holes on the back panel are at 16"; however, the lower two mounting holes are spaced at 19 7/8"; I guess the idea is the upper screws secure the cabinet to the wall; the lower for horizontal stability. I opted to drill holes at the 16" spaced spines for the bottom screws. Speaking of drilling holes, the back panel is solid, you will have to drill through the existing holes.The washers for the screws are but 3/4" diameter, seems a bit narrow for the load the cabinet maintains it can handle, even though the thickness of the wall "seems" adequate I decided to run a 1" x 1" board along the bottom for the cabinet to rest on. One added benefit of doing this is, when mounting, you can put the cabinet on this board and mount it yourself. Otherwise, it's a two person task.One other tidbit, the one shelf is centered vertically - 13" usable height space, cannot adjust, only the one shelf ledge.

I assembled and hung this myself! Super easy, follow directions. Heavy duty. Has one shelf. Size is perfect.There was excess material where the door meets the cupboard and it was rubbing and making a noise. Used a knife and cut it down and now it no longer makes a rubbing noise!

All parts perfectly aligned and easily went together. Instructions were clear. Extra small hardware was included, although not needed this time. Seems very sturdy and capable to handling the load and not warping and failing (unlike the particle board cabinet it is replacing which fell off the wall). One addition which simplifies mounting: adding a 3/4 by 3 by 30 inch board (actually less in my case since this was a remnant of the failed cabinet) at the bottom line of where the cabinet was to mount before installing. This makes it easier to level the cabinet during installation since the board is much easier to handle than the heavier and more awkward cabinet, and then the cabinet can be placed on the board edge for support while the mounting screws are aligned and attached making the whole process easier and more accurate. Also adds a little more weight bearing support and a nice surface for mounting power strips and hangers.

Pay attention to the well written assembly instructions, and it’s easy to pot together. Nice tight seal on doors and complimented our back porch

This is an excellent product. Was easy to assemble and fits plenty of gear for my weapons range. I highly recomend.